Loading...
Model: 998892101
T-18AU cavity and T-19AU cavity undercut tooling, straight shank
See CAD Files tab below to request images.
Technical specifications
This tool is used to generate the annulus, or undercut, for optimized T-18AU and T-19AU Series 4 Plus cavities.
- MaterialTiN coated high speed steel
Why is turning the adjust screw for counterbalance valves opposite of most other valves?
What parts of the Sun cartridge valve are field serviceable?
Does this FLeX series throttle control flow bidirectionally?
What are the shock and vibration levels the 740 coils are capable of withstanding?
Can the +5V reference on the XMD-02 be used in parallel to power two input devices?
How much current do XMD-01 and XMD-02 consume?
Can FLeX proportional valves be driven with an explosion proof coil?
How do I reset my XMD password?
Why won't my device connect to the XMD?
Why is the minimum opening pressure (bias spring pressure) on pilot-operated FLeX cartridges lower than competitor product?
What is the flow performance limit of pilot-operated FLeX cartridges?
Why won't the XMD send output to the coil when an input is provided?
What is the difference between nominal and maximum flow capacity?
What is the flow performance limit of DF** FLeX cartridges?
Do FLeX valves utilize a floating nose design?
Is the FLeX program available in QuickDesign SmartConnect?
Does the XMD Driver have an internal TVS Diode? Is a coil with or without diode recommended for use with the XMD?
The supply voltage range for the XMD Driver is 9-32VDC. Can I drive a 24V coil with a 12V supply, or a 12V coil with a 24V supply?
Does the +5V reference need to be used when using a resistive input option on the XMD Driver?
Can the XMD Series drivers be used to control non-FLeX coils or non-Sun coils?
What are the tolerances on pressure settings for Sun's pressure control valves?
What is the rated flow pressure drop?
I need to discharge a large accumulator. How can I increase the capacity of my discharge circuit?
Why doesn't Sun anodize their aluminum bodies?
How big do my slip orifices have to be?
What does Sun mean by the term sequencing?
What do I need to know about applying sequence valves?
Where would I use a kick-down relief?
Can I use a kick-down relief for my system relief?
What should I do if I need load holding on the rod of a high ratio cylinder?
What happens to the pilot-to-open check valve if I have back pressure in my system?
Other companies make high ratio PO checks. Why doesn't Sun?
Can I control the motion of a load with a pilot-to-open check valve?
What happens if I block the control flow (priority) port?
You say your valves leak 5 drops/min. How can I keep my load from drifting?
How do I determine the setting of a counterbalance valve?
Why do you call it a hammer valve?
How hot is hot?
How do I know how much pilot pressure is required to lower a load with a counterbalance valve?
How do I know how much pilot pressure is required to open a pilot-to-open check valve?
Why does Sun use 2 slip orifices?
I need a reducer on B. Can I connect the drain to A?
Where should I mount pilot-to-open check valves in my system?
Can I use pilot-to-open check valves with paired cylinders?
I have a heat problem, will Sun's priority flow control help?
Why am I getting a higher inaccuracy than Sun claims?
Most of the dividing-combining inaccuracies will average out, won't they?
Most of Sun's divider-combiners will do better than the published specs, won't they?
Can I synchronize two cylinders with Sun's divider-combiner?
When should I use a vented counterbalance valve?
How does Sun test a counterbalance valve for leakage?
How do I decide which pilot ratio to select?
What about intensification?
How big is a drop of hydraulic oil?
How do I get a kick-down relief to reset?
What do you mean by maximum differential?
Vented pilot-to-open check valves are insensitive to pressure on the valve port (port 2), aren't they?
Should I replace the pilot-to-open check valve if my cylinder is drifting or moving?
The LH*A looks like just the valve I need to pressure compensate my load-sense whatever. Will it work?
What is the pressure drop through a flow control?
What is the compensating pressure of Sun's flow controls?
What is the synchronizing feature?
How has Sun solved the hook breaking problem?
Why can't I use a counterbalance valve in a closed loop transmission circuit?
What do you mean by the setting of a counterbalance valve and what should it be?
I don't need pilot assist. Can I just block port 3?
Can I use an atmospherically vented counterbalance valve instead of the four-port version to save on plumbing?
Can I use a flow fuse to provide fire protection?
I need to charge an accumulator. What do I need to know?
Where should a vented valve be vented?
What is the actual pilot ratio of Sun's pilot to open check valves?
What ever happened to the Delrin seated valves?
What does pilot ratio refer to in a pilot-to-open check valve?
How can I assemble a stack of sandwiches and keep it dry?
Where would I use a DR__ instead of a DP__?
I used a DP** in a circuit but it hangs. What happened?
Why is it that your valves have pilot ratios below 10:1, while other manufacturers start at 7:1 and go up?
Why can't I block the pilot vent port? That area is positively sealed, isn't it?
Should I replace the counterbalance valve if my cylinder is drifting or moving?
I have a pilot-to-open check on a large cylinder and the decompression is violent. Can I use a counterbalance instead?
How do I size a counterbalance valve?
Can I adjust a counterbalance valve in the field?
Every time I try to lower my load the flow fuse trips. What's wrong?
How should I choose the setting of a flow fuse?
Can I use a flow fuse to prevent the loss of oil?
Why does Sun profile the ends of your sandwich manifolds? Is there a functional reason?
Direct acting or pilot operated - what do I use?
Will your reducing/relieving valve relieve my pump to tank?
Can I back flow through a reducing valve from port 1 to port 2?
What is the difference between pilot-to-open check valves with sealed pilots compared to standard bleed through versions?
My load keeps drifting, and every time I take your valves out, the nose seals have been blown out of their grooves.
I want to use your pilot-to-open checks on air. Will they work?
Can I use a three-port vented pilot-to-open check valve instead of the four-port version to save on plumbing?
What is a priority flow divider?
How accurate are Sun's flow controls?
Why do you offer 2 check valve cracking pressures?
What happens to the counterbalance valve if I have backpressure in my system?
What do you mean by hysteresis when referring to a counterbalance valve?
Your gage line fuse is just what I want, but I need a setting of 2 gpm (7,5 L/min.).
What happens if I block the bypass port on a priority flow control?
- Tool needs to insert 4.50 inches (114,3 mm) into body.
Highlights
Technical Tips
Technical Information