Search Error
Cartridges
Pressure Control
Reducing/Relieving
Loading...
Loading...

Model

PRBCLAN

Control
  • Standard Options
  • C
    Tamper Resistant - Factory Set
  • K
    Handknob
  • L
    Standard Screw Adjustment
Adjustment Range
  • Standard Options
  • A
    500 - 3000 psi (35 - 210 bar), 700 psi (50 bar) Standard Setting
  • B
    50 - 1500 psi (3,5 - 105 bar), 200 psi (14 bar) Standard Setting
  • D
    25 - 800 psi (1,7 - 55 bar), 200 psi (14 bar) Standard Setting
  • E
    25 - 400 psi (1,7 - 28 bar), 200 psi (14 bar) Standard Setting
  • W
    750 - 4500 psi (50 - 315 bar), 1000 psi (70 bar) Standard Setting
  • Additional Options
  • S
    25 - 200 psi (1,7 - 14 bar), 100 psi (7 bar) Standard Setting
Seal Material
  • Standard Options
  • E
    EPDM
  • N
    Buna-N
  • V
    Viton

Direct-acting, pressure reducing/relieving valve with open transition

Cavity: T-163A | Capacity:

Loading...

Model

PRBCLAN

Control
  • Standard Options
  • C
    Tamper Resistant - Factory Set
  • K
    Handknob
  • L
    Standard Screw Adjustment
Adjustment Range
  • Standard Options
  • A
    500 - 3000 psi (35 - 210 bar), 700 psi (50 bar) Standard Setting
  • B
    50 - 1500 psi (3,5 - 105 bar), 200 psi (14 bar) Standard Setting
  • D
    25 - 800 psi (1,7 - 55 bar), 200 psi (14 bar) Standard Setting
  • E
    25 - 400 psi (1,7 - 28 bar), 200 psi (14 bar) Standard Setting
  • W
    750 - 4500 psi (50 - 315 bar), 1000 psi (70 bar) Standard Setting
  • Additional Options
  • S
    25 - 200 psi (1,7 - 14 bar), 100 psi (7 bar) Standard Setting
Seal Material
  • Standard Options
  • E
    EPDM
  • N
    Buna-N
  • V
    Viton

Technical specifications

Direct-acting, pressure reducing valves reduce a high primary pressure at the inlet (port 2) to a constant reduced pressure at port 1. These valves incorporate a damped construction for stable operation allowing the use of high reduced pressure. This valve is open in the transition from reducing to relieving. It provides good pressure control and dynamic response.

  • Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 3000 psi (210 bar).
  • Leakage specified in Technical Data is out of port 3 with a supply pressure of 2000 psi (140 bar) and the valve set at mid range. This leakage is directly proportional to pressure differential and inversely proportional to viscosity expressed in centistokes.
  • The transition from reducing to relieving is slightly open. The result is very good pressure control with oil consumption of about 0.1 gpm (0,4 L/min.).
  • All three-port pressure reducing and reducing/relieving cartridges are physically interchangeable (i.e. same flow path, same cavity for a given frame size). When considering mounting configurations, it is sometimes recommended that a full capacity return line (port 3) be used with reducing/relieving cartridges.
  • Full reverse flow from reduced pressure (port 1) to inlet (port 2) may cause the main spool to close. If reverse free flow is required in the circuit, consider adding a separate check valve to the circuit.
  • All spring ranges are tested for correct operation with 5000 psi (350 bar) inlet pressure.
  • Direct acting concept provides highly reliable operation in contaminated systems, especially at dead headed conditions.
  • Direct operated version offers superior dynamic response compared to equivalent pilot operated models.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.
Back to Top
  • Cavity
    T-163A
  • Series
    0
  • Capacity
    5 gpm
  • Maximum Operating Pressure
    5000 psi
  • Factory Pressure Settings Established at
    0.25 gpm
  • Maximum Valve Leakage at 110 SUS (24 cSt)
    20 in³/min.
  • Adjustment - No. of CW Turns from Min. to Max. setting
    7
  • Valve Hex Size
    3/4 in.
  • Valve Installation Torque
    20 - 25 lbf ft
  • Adjustment Screw Internal Hex Size
    5/32 in.
  • Locknut Hex Size
    1/2 in.
  • Locknut Torque
    80 - 90 lbf in.
  • Model Weight
    .30 lb
  • Seal kit - Cartridge
    Buna: 990-163-007
  • Seal kit - Cartridge
    Viton: 990-163-006

Model CAD Files

Click the link of the file format you want to download.

PRBCLAN.dwg
PRBCLAN.dxf
PRBCLAN.prt
PRBCLAN.stp

Symbol CAD Files

Click the link of the file format you want to download.

Back to Top
  • What parts of the Sun cartridge valve are field serviceable?
  • What are the tolerances on pressure settings for Sun's pressure control valves?
  • I need a reducer on B. Can I connect the drain to A?
  • How big is a drop of hydraulic oil?  
  • What do you mean by maximum differential?
  • Direct acting or pilot operated - what do I use?
  • Will your reducing/relieving valve relieve my pump to tank?
  • Can I back flow through a reducing valve from port 1 to port 2?
    • Back to Top

Keep up with Sun