Search Error
Cartridges
Pressure Control
Reducing/Relieving

Model

PVHALAN

Control
  • Standard Options
  • C
    Tamper Resistant - Factory Set
  • L
    Standard Screw Adjustment
  • Additional Options
  • K
    Handknob
Adjustment Range
  • Standard Options
  • A
    100 - 3000 psi (7 - 210 bar), 200 psi (14 bar) Standard Setting
  • B
    50 - 1500 psi (3,5 - 105 bar), 200 psi (14 bar) Standard Setting
  • D
    25 - 800 psi (1,7 - 55 bar), 200 psi (14 bar) Standard Setting
  • E
    25 - 400 psi (1,7 - 28 bar), 200 psi (14 bar) Standard Setting
  • W
    150 - 4500 psi (10,5 - 315 bar), 200 psi (14 bar) Standard Setting
  • Additional Options
  • H
    30 - 3000 psi (2 - 210 bar), 200 psi (14 bar) Standard Setting
  • J
    25 - 1500 psi (1,7 - 105 bar), 200 psi (14 bar) Standard Setting
Seal Material
  • Standard Options
  • E
    EPDM
  • N
    Buna-N
  • V
    Viton
Material/Coating
  • Standard Options
  • Standard Material/Coating
  • /AP
    Stainless Steel, Passivated

Model: PVHA

Pilot-operated, pressure reducing/relieving valve with drain to port 4

Cavity: T-23A | Capacity:

Model

PVHALAN

Control
  • Standard Options
  • C
    Tamper Resistant - Factory Set
  • L
    Standard Screw Adjustment
  • Additional Options
  • K
    Handknob
Adjustment Range
  • Standard Options
  • A
    100 - 3000 psi (7 - 210 bar), 200 psi (14 bar) Standard Setting
  • B
    50 - 1500 psi (3,5 - 105 bar), 200 psi (14 bar) Standard Setting
  • D
    25 - 800 psi (1,7 - 55 bar), 200 psi (14 bar) Standard Setting
  • E
    25 - 400 psi (1,7 - 28 bar), 200 psi (14 bar) Standard Setting
  • W
    150 - 4500 psi (10,5 - 315 bar), 200 psi (14 bar) Standard Setting
  • Additional Options
  • H
    30 - 3000 psi (2 - 210 bar), 200 psi (14 bar) Standard Setting
  • J
    25 - 1500 psi (1,7 - 105 bar), 200 psi (14 bar) Standard Setting
Seal Material
  • Standard Options
  • E
    EPDM
  • N
    Buna-N
  • V
    Viton
Material/Coating
  • Standard Options
  • Standard Material/Coating
  • /AP
    Stainless Steel, Passivated

Technical specifications

Externally drained, pilot-operated pressure reducing/relieving valves reduce a high primary pressure at the inlet (port 2) to a constant reduced pressure at port 1, with a full-flow relief function from port 1 to tank (port 3). Draining the pilot section at port 4 makes these valves insensitive to pressure at tank (port 3) and provides a means for remote control by pilot or 2-way valves.

  • Maximum pressure at port 3 should be limited to 3000 psi (210 bar).
  • Pilot operated valves exhibit very low dead-band transition between reducing and relieving modes.
  • Recommended maximum inlet pressure is determined by the adjustment range. Ranges D, E, N, and Q are tested with a 2000 psi (140 bar) maximum differential between inlet and reduced pressure. Ranges A, B, and H are tested with a 3000 psi (210 bar) maximum differential between inlet and reduced pressure. Ranges C and W are tested with 5000 psi (350 bar) of inlet pressure.
  • Pressure at port 4 should not exceed 5000 psi (350 bar).
  • Pilot operated valves exhibit exceptionally flat pressure/flow characteristics, are very stable and have low hysteresis.
  • Pressure on the drain (port 4) is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi (350 bar).
  • Pilot operated reducing, reducing/relieving valves by nature are not fast acting valves. For superior dynamic response, consider direct acting valves.
  • Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
  • By controlling the pressure at the drain (port 4), the effective setting of the valve can be increased over the nominal valve setting.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.
Back to Top
  • Cavity
    T-23A
  • Series
    3
  • Capacity
    40 gpm
  • Maximum Operating Pressure
    5000 psi
  • Control Pilot Flow
    15 - 20 in³/min.
  • Factory Pressure Settings Established at
    blocked control port (dead headed)
  • Adjustment - No. of CW Turns from Min. to Max. setting
    5
  • Valve Hex Size
    1 1/4 in.
  • Valve Installation Torque
    150 - 160 lbf ft
  • Adjustment Screw Internal Hex Size
    5/32 in.
  • Locknut Hex Size
    9/16 in.
  • Locknut Torque
    80 - 90 lbf in.
  • Model Weight
    1.30 lb
  • Seal kit - Cartridge
    Buna: 990-023-007
  • Seal kit - Cartridge
    EPDM: 990-023-014
  • Seal kit - Cartridge
    Polyurethane: 990-023-002
  • Seal kit - Cartridge
    Viton: 990-023-006

Model CAD Files

Files not yet avialable. Click below to request them.

Back to Top
  • What parts of the Sun cartridge valve are field serviceable?
  • What are the tolerances on pressure settings for Sun's pressure control valves?
  • I need a reducer on B. Can I connect the drain to A?
  • How big is a drop of hydraulic oil?  
  • What do you mean by maximum differential?
  • Direct acting or pilot operated - what do I use?
  • Will your reducing/relieving valve relieve my pump to tank?
  • Can I back flow through a reducing valve from port 1 to port 2?
    • Back to Top
  • Maximum pressure differentials for spring ranges: A and B are 3000 psi (210 bar) D and E are 2000 psi (140 bar) W is 5000 psi (350 bar) inlet pressure
Back to Top
  • PVHA8 Pilot-operated, pressure reducing/relieving main stage with integral T-8A control cavity and drain to port 4
    • Back to Top