Search Error
Solutions
Regeneration
Loading...
Loading...

Model

YDEWXCNB

Control
  • Standard Options
  • X
    Not Adjustable
Cracking Pressure
  • Standard Options
  • A
    4 psi (0,3 bar)
  • B
    15 psi (1 bar)
  • C
    30 psi (2 bar)
  • D
    50 psi (3,5 bar)
  • F
    100 psi (7 bar)
  • Z
    1 psi (0,07 bar)
  • Additional Options
  • E
    75 psi (5 bar)
Seal Material
  • Standard Options
  • N
    Buna-N
  • V
    Viton
Primary Cartridge
  • Standard Options
  • B
    B (with CXEE primary cartridge, Free flow side to nose check valve with port 3 blocked)
Model: YDEW

Full time regenerative assembly

Capacity:

Loading...

Model

YDEWXCNB

Control
  • Standard Options
  • X
    Not Adjustable
Cracking Pressure
  • Standard Options
  • A
    4 psi (0,3 bar)
  • B
    15 psi (1 bar)
  • C
    30 psi (2 bar)
  • D
    50 psi (3,5 bar)
  • F
    100 psi (7 bar)
  • Z
    1 psi (0,07 bar)
  • Additional Options
  • E
    75 psi (5 bar)
Seal Material
  • Standard Options
  • N
    Buna-N
  • V
    Viton
Primary Cartridge
  • Standard Options
  • B
    B (with CXEE primary cartridge, Free flow side to nose check valve with port 3 blocked)
See CAD Files tab below to request images.
Function
B to A
Function image

Technical specifications

The full time regenerative valve assembly allows a double-acting, single rod cylinder to be extended more rapidly using the same pump flow. To achieve this, oil from the rod end of the cylinder is added to the flow to the blind end, increasing the rate of extension.

  • Capacity refers to pump flow or regeneration flow, which is the flow coming out of the rod side of the cylinder, whichever is larger
  • The capacity may be determined by the passages dictated by the sandwich pattern rather than the cartridge capacity.
  • This valve assembly will not prevent a load from extending the cylinder. The best way to prevent this is to use a vented counterbalance valve mounted directly to the rod end of the cylinder. A non-vented valve will not work.
  • The ideal cylinder ratio to use with regeneration is 2:1, the blind end area being twice what the annular area at the rod end. A 2:1 cylinder in regen gives the same speed extending as retracting.
  • Cylinders with ratios above 2:1 (large rods) will function correctly but with less speed gain. Intensification needs to be considered with higher ratios. A 2:1 cylinder may generate a pressure on the rod side that is twice system pressure unless steps are taken to limit it.
  • Cylinders with ratios as low as 1.5:1 (small rods) may work if care is used in designing the application. As the rod diameter gets smaller in relation to the piston diameter the flows increase dramatically and the force available drops accordingly.
  • Cylinders with ratios below 1.5:1 are unlikely to result in a working regenerative application because of the small area of the rod and the high flows that would be generated.
  • When a cylinder is in the regenerative mode the only force available is the pressure working on the rod area.
  • Regeneration is only possible in the extend direction.
Back to Top
  • Body Type
    Sandwich
  • Interface
    ISO 05 - X&Y
  • Capacity
    25 gpm
  • Body Features
    B to A
  • Seal Plate Included (see notes)
    No
  • Stack Height
    2.49 in.

Model CAD Files

Files not yet avialable. Click below to request them.

Back to Top
  • Why doesn't Sun anodize their aluminum bodies?
  • How big is a drop of hydraulic oil?  
  • Direct acting or pilot operated - what do I use?
    • Back to Top
  • 990120009 ISO 05 X and Y US sandwich manifold retainer and buna-N seal kit
  • 990120010 ISO 05 X and Y US sandwich manifold retainer and Viton seal kit
  • 990120011 ISO 05 X and Y Europe sandwich manifold retainer and Viton seal kit
  • 990120012 ISO 05 X and Y Europe sandwich manifold retainer and buna-N seal kit
    • Back to Top
  • Stack height value in technical data table includes seal retainer plate.
  • This installation requires a seal retainer plate and seal kit which are purchased separately. See "Related Accessories" section.
  • For detailed information regarding the cartridges contained in this assembly, click on the models codes shown in the Included Components tab.
  • Important: Carefully consider the maximum system pressure. The pressure rating of the manifold is dependent on the manifold material, with the port type/size a secondary consideration. Manifolds constructed of aluminum are not rated for pressures higher than 3000 psi (210 bar), regardless of the port type/size specified.
Back to Top

Keep up with Sun